Blue-sea-systems 8509 AC Main + 3 Positions [European] Manuel d'utilisateur télécharger pdf

Marine Electrical Prod

ucts

Panel Speciﬁ cations

Voltage Rating: PN 8074 / 3074 / 8409 / 3409 120 Volts AC

PN 8174 / 3174 / 8509 / 3509 230 Volts AC

Panels are rated for these voltages and are so

marked in order to comply with ABYC standards.

Amperage Rating: Panel Buses are sized for 100 Amperes of

continuous current.

Material: 0.125” 5052-H32 Aluminum Alloy

Primary Finish: Chemical Treatment per Mil Spec C-5541C

Final Panel Finish: Graphite color 2 part textured Polyurethane

Overall Inches Millimeters PN

Dimensions: 5.25” x 11.25” 133.4mm x 285.8mm 8074/3074/8174/3174

5.25” x 7.50” 133.4mm x 190.5mm 8409/3409/8509/3509

Mounting 4.42” x 10.42” 112.3mm x 264.7mm 8074/3074/8174/3174

Centers: 4.44” x 6.69” 112.8mm x 169.9mm 8409/3409/8509/3509

Panel Features

PN 8074/PN 3074/PN 8174/PN 3174/PN 8409/PN 3409/PN 8509/PN 3509

• E marked, Complies with European Standards

• 0-50 Ampere AC Ammeter

PN 8074 / PN 3074 / PN 8409 / PN 3409 - 120 Volt AC

• One double-pole 30 Ampere AC main circuit breaker

• PN 8074 / PN 3074 - ﬁ ve 15 Ampere branch circuit breakers installed

• PN 8409 / PN 3409 - three 15 Ampere branch circuit breakers installed

• 0-150 Volt AC voltmeter

PN 8174 / PN 3174 / PN 8509 / PN 3509 - 230 Volt AC

• One double-pole 16 Ampere AC main circuit breaker

• PN 8174 / PN 3174 - ﬁ ve 8 Ampere branch circuit breakers installed

• PN 8509 / PN 3509 - three 8 Ampere branch circuit breakers installed

• 0-250 Volt AC voltmeter

Blue Sea Systems Inc. Phone (360) 738-8230

425 Sequoia Drive Fax (360) 734-4195

Bellingham, WA 98226 USA E-mail [email protected]

www.bluesea.com

Document 9976 Rev.F

WARNING

@ It is not possible within the scope of these instructions to fully acquaint

the installer with all the knowledge of electrical systems that may be

necessary to correctly install this product. If the installer is not

knowledgeable in electrical systems we strongly recommend that an

electrical professional be retained to make the installation.

@ If either the panel front or back is to be exposed to water it must be

protected with a waterproof shield.

@ The panels must not be installed in explosive environments such as

gasoline engine rooms or battery compartments as the circuit breakers

are not ignition proof.

@ The vessel’s shore power cord must be disconnected form shoreside

power before installing this electrical panel.

@ If an inverter is installed on the vessel its power leads must be

disconnected at the battery before the panel installation. Be aware that

many inverters have a “sleep mode” in which their voltage potential

may not be detectable with measuring equipment.

@ If an AC Generator is installed aboard it must be stopped and rendered

inoperable before the panel is installed.

@ Verify that no other AC source is connected to the vessels’ wiring

before the panel is installed.

Guarantee

Any Blue Sea Systems’ product with which a customer is not satisﬁ ed

may be returned for a refund or replacement at any time.

Installation

1. Disconnect all AC and DC power

Disconnect all AC power originating on or off the vessel. This includes

inverters, generators, shore power attachments and any other device

capable of supplying AC power to the ship’s circuits.

Disconnect the main positive DC cable from all batteries to eliminate

the possibility of a short circuit and to disable the inverter while

installing the distribution panel.

2. Select mounting location and cut opening

If this panel is to serve as your main shore power disconnect circuit

breaker, select a location which is not more then 10 feet from the shore

power inlet or the electrical attachment point of a permanently installed

shore power cord as measured along the conductors of the feed wires.

If it is more then 10 feet additional fuses or circuit breakers must be

installed within 10 feet of the shore power inlet.

Select a mounting location which is protected from water on the panel

front and back and is not in an area where ﬂ ammable vapors from

propane, gasoline or lead acid batteries accumulate. The circuit

breakers used in marine electrical panels are not ignition protected and

may ignite such vapors.

Using the panel template provided, make a cut out in the mounting

surface where the distribution panel is to be mounted. Do not yet

fasten the panel to the mounting surface.

3. Install branch circuit wires

Determine the proper wire size for each branch circuit using the chart

below. Verify that the standard circuit breakers installed in the panel

are correct for each branch circuit. Remove and replace any that are

incorrectly sized. The circuit breaker must have a rating less than the

allowable amperage of the wire, yet greater than the circuit’s

continuous current.

AC Main Power Distribution Panels

PN 8074 / PN 3074 / PN 8174 / PN 3174

PN 8409 / PN 3409 / PN 8509 / PN 3509

Connect each branch circuit hot (black) to the appropriate load terminal.

Connect each branch circuit neutral (white) to one of the screws on the

neutral bus. Connect each branch safety ground wire (green) to one of

the screws of the safety ground bus.

Do not confuse the neutral current carrying wires (sometimes called

ground) with the green normally non-current carrying wires (sometimes

called grounding). These two wires must be connected only at the

source of power, nowhere else.

Wire sizing chart

Use the wire sizing chart below to determine the proper branch and

feed circuit wire sizes.

Allowable Amperage of Conductors

Note: This chart assumes wire with 105°C insulation rating

and no more then 2 conductors are bundled.

Not suitable for sizing ﬂ exible shore power cords.

1 2

Résumé du contenu

Page 1 - Installation

Marine Electrical ProductsPanel Speciﬁ cations Voltage Rating: PN 8074 / 3074 / 8409 / 3409 120 Volts AC PN 8174 / 3174 / 8509 / 3509 230 Volt

Page 2 - Installation (continued)

Installation (continued) 4. Install feed circuit wires Install the feed wires from the shore power inlet or other AC source, referring to the wir

Commentaires sur ces manuels

Pas de commentaire

Blue-sea-systems 8509 AC Main + 3 Positions [European] Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Panneau de contrôle Blue-sea-systems 8509 AC Main + 3 Positions [European]. Blue Sea Systems 8509 AC Main + 3 Positions [European] User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Panneau de contrôle Blue-sea-systems 8509 AC Main + 3 Positions [European]